USERS’ INSTALLATION OPERATION AND MAINTENANCE MANUAL WARNING: If the information in this manual is not followed exactly, fire or explosion may result
OPTIMA 22 10 LEVELING THE OPTIMA 22 DIRECT VENT INSERT Before placing the appliance into the fireplace, ch
OPTIMA 22 11 The Optima 22 requires two flexible gas flue liners: Flue Collar (inlet) - 3” (76 mm) diame
OPTIMA 22 12 Instructions for use with Archgard vertical termination cap - Part # 999-INS-TK. Install the te
OPTIMA 22 13 SURROUND INSTALLATION Make sure the gas and electrical lines are properly connected to the ap
OPTIMA 22 14 If a wall-mounted switch or a wall-mounted thermostat is desired, Archgard recommends that the
OPTIMA 22 15 LOG PLACEMENT WARNING: Failure to position the parts in accordance with these diagrams or fai
OPTIMA 22 16 LOG PLACEMENT... Continued Step 1. Locate right log and place it on the locater pins as shown.
OPTIMA 22 17 LOG PLACEMENT... Continued Step 3. Locate the left log and place it on the two left locater pin
OPTIMA 22 18 LOG PLACEMENT... Continued Step 5. Locate the top right log so the top bottom burnt part of the
OPTIMA 22 19 The Archgard brick and reflective glass panels offer a variety of looks to customize your fire-
5.08: Modifications to NFPA-54, Chapter 10 (2) Revise 10.8.3 by adding the following additional requirements: (a) For all side wall horizontally vent
OPTIMA 22 20 INITIAL OPERATION 1. Check that the appliance is properly vented and connected to the gas supp
OPTIMA 22 21 This appliance has a pilot which must be ignited using the sparker located next to the applianc
OPTIMA 22 22 1. Set the thermostat to the lowest setting and turn the remote switch to “OFF”. 2. Turn off
OPTIMA 22 23 GLASS DOOR REMOVAL CAUTION: Do not attempt to remove the glass door when the appliance is hot.
OPTIMA 22 24 OPTIONAL BAY DOOR INSTALLATION CAUTION: Only trim kit (s) supplied by the manufacturer may be
OPTIMA 22 25 TROUBLESHOOTING SYMPTOM ACTION Pilot will not light after pressing the sparker many times. 1.
OPTIMA 22 26 TROUBLESHOOTING Cont... SYMPTOM ACTION The main burner does not turn on with the pilot lit. Co
OPTIMA 22 27 Regularly: Frequent cleaning of the ceramic glass is required. Archgard recommends using a
OPTIMA 22 28 Before servicing, read the terms and conditions of the Archgard warranty at the back of the man
OPTIMA 22 29 ADJUSTING PRIMARY AIR NOTE: Fig. 1 Is to give an example of what a correct or incorrect flame p
INTRODUCTION Congratulations on choosing an Archgard Gas Fireplace! The Optima 22 Direct Vent Insert is one of the most advanced Direct Vent Insert h
OPTIMA 22 30 1. Open the lower grills. 2. The pressure test taps are located on the valve. The taps are lo
OPTIMA 22 31 REPLACING CONVECTION BLOWER CAUTION: Label all wires prior to disconnection when servicing cont
OPTIMA 22 32 Item # Item Description Qty Unit A 308-0043 Valve, ROBERTSHAW, Hi/Low Natural Gas 1 EA
OPTIMA 22 33 PARTS LIST - Logs and Pan Burner Pan Burner Item # Item Description Qty Unit 310-6222-1 Lo
OPTIMA 22 34 REPLACEMENT PARTS LIST - ARCHGARD OPTIMA 22 Item # Item Description Qty Unit 200-1914 Owne
OPTIMA 22 35 REPLACEMENT PARTS LIST FOR THE ARCHGARD OPTIMA 22 Item # Item Description Qty Unit Replacem
This Limited Warranty is made by ARCHGARD INDUSTRIES LTD., hereinafter referred to as “Archgard”. Archgard warrants to the original purchaser of an
OPTIMA 22 37 FREQUENTLY ASKED QUESTIONS Listed below are some frequently asked questions regarding Archgard
OPTIMA 22 38 NOTES
Postage WARRANTY REGISTRATION ARCHGARD INDUSTRIES LTD. 7116 BEATTY DRIVE MISSION, B.C. CANADA V2V 6B4 FOLD DOWN AT LINE FOLD DOWN AT LINE & TAPE
TABLE OF CONTENTS Caution and Safety Instructions 5 Appliance Certification, Installation Codes and Specifications 6 Appliance Dimensions and Minimu
Archgard Industries Ltd. 7116 Beatty Drive Mission, B.C. V2V 6B4 Canada Website: www.archgard.com
OPTIMA 22 5 Due to high temperatures, the appliance should be located out of traffic and away from furniture
OPTIMA 22 6 This appliance is tested and certified to the following USA and Canadian gas appliance standards
OPTIMA 22 7 MINIMUM FIREPLACE DIMENSIONS J SIDE VIEW For twin 3” liners, minimum flue size required is 4”
OPTIMA 22 8 CLEARANCES TO COMBUSTIBLES TOP VIEW SIDE VIEW Clearances to Faceplate 1” (25 mm) 1” (25 mm) Sid
OPTIMA 22 9 Before connecting the appliance to the gas supply line, double check that the appliance you have
Kommentare zu diesen Handbüchern